We Have More Than 10 Years of Experience.
   
   
top-ban
  1. HOME > News

Common problems and solutions of the wetting device of xenon lamp aging tester

2023-01-03

The humidification function of the xenon lamp aging tester mainly uses a humidifier, so if the humidity in the xenon lamp climate test chamber is unstable, there may be a problem with the equipment's humidifier in general. QINSUN Instruments Co., Ltd. is a manufacturer of aging equipment. The R&D engineers will introduce the common problems of humidifiers and their treatment methods below, hoping to help customers.

1. The humidifier sink is not enough.

Answer: Add water. Remove the steam pipe, lift the water tank to release it from the base, turn the water tank upside down, open the water filling lid and add a certain amount of water to the water tank. After the water injection is completed, tighten the water cap and check the water cap and spring valve. (Exit) Whether there is a drip. Place the tank on the bottomdup as required by the coupling - the tank will fit on the bottom.

2. The steam circuit of the xenon lamp aging test chamber is poorly connected.

Treatment method: Place the humidifier on the ground behind the right side of the artificial climate box, then insert the steam exhaust pipe into the gas production pipe, and use a special soft plastic tube to connect the steam exhaust pipe from the humidifier to the artificial climate box. Keep the angle of the steam inlet pipe > 3°, and avoid the plastic pipe hanging or flattening, so as not to block the steam path by water accumulation.

3. There is a problem with the circuit connection.

Treatment method: Plug the plug into the socket on the right and back of the humidifier before use. The power supply to the humidifier is controlled by a climate cabinet to ensure humidity.

In addition, if there is a problem with the operating system of theaging test chamber of the xenon lamp or if there is a problem with the humidification pump, you should contact the technical personnel of the manufacturer to solve this situation . Undoing the damage during repair itself can also pose safety issues. Reporting to the manufacturer for repair is therefore a more effective solution.

Humidification function of xenon lamp aging tester

Lab

Humidifiers are mainly used, so if the humidity in the xenon lamp climate test chamber is unstable, there may be a problem with the equipment humidifier in general. QINSUN Instruments Co., Ltd. is a manufacturer of aging equipment. The R&D engineer will introduce the humidifier below. The common problems and their solutions hope to help customers.

1. The humidifier sink is notEnough.

Answer: Add water. Remove the steam pipe, lift the water tank to release it from the base, turn the water tank upside down, open the water filling lid and add a certain amount of water to the water tank. After the water injection is completed, tighten the water cap and check the water cap and spring valve. (Exit) Whether there is a drip. Place the tank on the bottom cap as required by the coupling - the tank will fit on the bottom.

2. The steam circuit of the xenon lamp aging test chamber is poorly connected.

Treatment method: Place the humidifier on the ground behind the right side of the artificial climate chamber, then insert the steam discharge pipe into the gas production pipe and connect the steam discharge pipe of the humidifier with a special soft plastic pipe Keep an angle of >3° with the steam inlet pipe of the artificial climate chamber and prevent the plastic pipe from hanging or plaitingto prevent the steam path from becoming clogged by water accumulation.

3. There is a problem with the circuit connection.

Treatment method: Plug the plug into the socket on the right and back of the humidifier before use. The power supply to the humidifier is controlled by a climate cabinet to ensure humidity.

In addition, if there is a problem with the control system of the xenon lamp aging test chamber, or if there is a problem with the humidification pump, you must contact the manufacturer's technical personnel to solve this situation . Undoing the damage while it repairs itself can also pose security issues. Reporting to the manufacturer for repair is therefore a more effective solution.

What Can I Do For You?

You can Send Message or email info@qinsun-lab.com to us, we will reply tu you within 24 hours.Now tell us your need,there will be more favorable prices!

toTop